- 您现在的位置：买卖IC网 > Sheet目录942 > 626051-000 (TE Connectivity)SOLDER PAK WIRE TERMINATORS
SPECIFICATION CONTROL DRAWING
THERMOFIT ASSEMBLY PROCEDURE
SolderSleeve and Lead in Position for Assembly
INSTALLATION PROCEDURE:
1. Terminals must be tinned prior to placement of sleeves.
2. Cut the correct number of sleeves from the reel.
3. Position sleeves onto connector terminals as shown above and remove carrier tape.
4. Strip wire 4.83±0.51 (0.19±0.02) and pre-tin.
5. Insert wires onto sleeves. Wires should be straight and parallel to terminal.
6. Heating Technique:
a. Infrared Heater IR-1012: Position connector into holding fixture. Place leads to be connected
into correct sleeve, (Sleeve will accept up to two 24 AWG leads). Position heater and energize,
after setting timer for correct cycle. Refer to IR-1012 Solder Pak Operating Instructions for
detailed procedure and maintenance instructions.
b. Convection Heater CV4505: Position connector into holding fixture. Place leads to be
connected into correct sleeve. Regulate airflow through the nozzle to achieve an air
temperature of 600° - 650°F at a point 7.62 (0.30) from the nozzle, (about 2.5 to 3 psi).
Apply heat until solder flow is noted.
Tyco Electronics Corporation
300 Constitutional Drive
Menlo Park, CA 94025 USA
TITLE: SOLDERPAK ASSEMBLY,
PCB CONNECTOR
1.42x0.23x5.08 (0.056x0.009x0.200) Terminals
with 2.54 (0.100) center spacing
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS.
INCHES DIMENSIONS ARE BETWEEN BRACKETS.
DOCUMENT NO.:
D-714-01
TOLERANCES:
0.00 N/A
0.0 N/A
ANGLES: N/A
ROUGHNESS IN
Tyco reserves the right to amend this drawing
at any time. Users should evaluate the
suitability of the product for their application.
DATE:
18-July-00
DOC ISSUE:
1
0 N/A
MICRON
DRAWN BY:
M. FORONDA
CAGE CODE:
06090
REPLACES:
N/A
DCR NUMBER:
D000405
PROD. REV.:
D
SCALE:
None
SIZE:
A
SHEET:
2 of 2
If this document is printed it becomes uncontrolled. Check for the latest revision.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
6269
REPLACE SCREWS #2-56 PAN HEAD
6278016-5
CABLE ASSY SC-SC DUPLEX MM 5M
6278153-1
MT-RJ LOOPBACK 62.5/125
6278357-1
MT-RJ LOOPBACK MM BARE
5SGXMA5N3F45I3LN
FPGA - 现场可编程门阵列 FPGA - Stratix V GX 2304 LABS 840 IOs
6316-96
PLUGS WE310 Y-RJ45/RJ48 PLUG
6317-96
PLUGS WE310 Y/9-PIN MALE CABLE
6318-96
PLUGS WE310 Y/15-PIN FMALE CABLE
相关代理商/技术参数
626-0527
制造商:TE Connectivity 功能描述:
626-0546
制造商:TE Connectivity 功能描述:
626056
功能描述:集管和线壳 HOUSING 4P .110 FASTIN-ON TAB
RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector
626056-1
制造商:TE Connectivity 功能描述:.110 FF REC. HSG4 W - Bulk
626056-4
功能描述:集管和线壳 HOUSING 4P .110 FASTIN-ON REC. RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector
626056-5
功能描述:FASTIN-ON .110 HOUSING RECEPTACL 制造商:te connectivity amp connectors 系列:Fastin-Faston 零件状态:在售 样式:体座 端子类型:快速连接，断开 公母:母型，插座 端子尺寸:0.110"（2.79mm） 针脚数:4 堆叠方向:顶部至底部以及侧面至侧面 配套使用产品/相关产品:0.110"（2.79mm）快速连接 安装类型:自由悬挂 颜色:红色 材料:聚酰胺（PA46），尼龙 4/6 备注:不含触头 标准包装:10,000
626057
功能描述:集管和线壳 TERM
RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector
626057-1
功能描述:集管和线壳 HOUSING 4P .110 FASTIN-ON TAB RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector